My Sump Pump Stopped Working! What To Do?

A sump pump is a device installed in the basement or crawlspace of a home. It is used to pump water out of the house to prevent flooding. A sump pump typically has a float switch that turns the pump on when the water level rises and turns it off when the water level drops.

If your sump pump has stopped working, it is essential to take action immediately to prevent flooding. This blog post will discuss the common reasons for sump pump problems and tips on what to do if your pump stops working.

Common Reasons Sump Pump Stop Working

Here are the three most common reasons why a sump pump will stop working:

Power Outage

If your sump pump has stopped working, the first thing you should do is check the power source. Next, ensure the pump is plugged in, and the circuit breaker has not been tripped.

Float Switch

If you have checked the power source and the float switch and your sump pump still does not seem to be working, the problem may be with the impeller. The impeller is the part of the sump pump that moves water through the pump. If the impeller is broken, the pump will not be able to move water and needs to be replaced.

Debris in Sump Pump

Another common reason for a sump pump to stop working is debris in the pump. Debris can build up over time, eventually blocking the impeller from moving freely. This will prevent the pump from being able to move water, and it will need to be cleaned out. To clean out a sump pump, you must unplug it and remove the impeller. Once the impeller is removed, you can use a brush to remove any debris blocking it.

Blown Fuse

If your sump pump has a blown fuse, it must be replaced. Fuses can blow for various reasons, but the most common reason is that the pump is overloaded. If you have a blown fuse, you will need to replace it with a new one of the same amperage.

Worn Out Motors

Another common reason a sump pump stops working is the motor has worn out. Sump pumps typically have a lifespan of about ten years. If your sump pump is older than 10 years, it may be time to replace the entire unit.

Broken Check Valve

If your sump pump has a broken check valve, then water can start to flow back into the pit after the pump has turned off. This can cause the pump to constantly cycle on and off, eventually leading to the motor burning out. If you think your sump pump has a broken check valve, you should take it to a professional for repair or replacement.

What To Do If Your Sump Pump Has Stopped Working

If your sump pump has stopped working, it is important to take action immediately to prevent flooding. Here are some tips on what to do if your sump pump has stopped working:

1) Check the power source

Ensure the pump is plugged in and the circuit breaker has not been tripped. Take immediate measures to correct the power source if necessary.

2) Check the float switch

If the float switch is not working properly, it will prevent the pump from turning on. First, check the float switch and ensure it is not stuck in the “on” position. It is the most common sump pump problem.

3) Clean out the pump

If debris is blocking the impeller, you must unplug the pump and remove the impeller. Once the impeller is removed, you can use a brush to remove any debris blocking it.

4) Replace a blown fuse

If your sump pump has a blown fuse, you will need to replace it with a new one of the same amperage.

5) Replace an old or worn-out pump

If your sump pump is over 10 years old, it may be time to replace the entire unit.

6) Take the pump to a professional

If your sump pump has a broken check valve, it will need to be repaired or replaced by a professional.

Taking action immediately is crucial if your sump pump has stopped working. Following these tips can prevent flooding and ensure that your pump works properly.

Repair vs. Replacement

If your sump pump has stopped working, you may be wondering if you should repair or replace the unit. There are a few factors to consider when making this decision:

Cost

Replacing a sump pump can be expensive, so repairing the unit may be a more cost-effective option.

Age of the unit

If your sump pump is over 10 years old, it may be time to replace it.

The severity of the problem

If your sump pump has a major problem, such as a broken check valve, it will need to be replaced.

Frequency of use

If your sump pump is used frequently, replacing it may be better than repairing it.

Consider these factors when deciding whether to repair or replace your sump pump. If you are unsure, it is always best to consult a professional.

Preventative Maintenance

The best way to avoid repairing or replacing your sump pump is to perform regular maintenance on the unit. This includes cleaning the unit regularly and checking for any signs of wear and tear. By performing regular maintenance, you can extend the lifespan of your sump pump and keep it working properly for years to come.

Final Words

We hope this guide has helped you troubleshoot your sump pump issue. If your sump pump has stopped working, taking action immediately is crucial to prevent flooding. Remember to check the power source, float switch, and impeller for debris. You may also need to replace a blown fuse or an old or worn-out pump. If your sump pump has a broken check valve, take it to a professional for repair or replacement.

Performing regular maintenance on your sump pump is the best way to avoid repairs or replacements. By cleaning the unit regularly and checking for signs of wear and tear, you can keep your sump pump working properly for years to come.

Thanks for reading!

Sump Pump Advisor
Logo